1 publication order number : nsvj3557a3/d ? semiconductor components industries, llc, 2015 july 2015 - rev. 0 www.onsemi.com nsvj3557sa3 automotive jfet designed for compact and efficient designs and including high gain performance. aec-q101 qualified jfet and ppap capable suitable for automotive applications. features ? large | yfs | ? small ciss ? this small package enables sets to be smaller and thinner ? ultralow noise figure ? pb-free and rohs compliance ? aec-q101 qualified and ppap capable typical applications ? am tuner rf amplifier ?? low noise amplifier specifications absolute maximum ratings at ta = 25c (note 1) parameter symbol value unit drain-to-source voltage v dsx 15 v gate-to-drain voltage v gds ? 15 v gate current i g 10 ma drain current i d 50 ma allowable power dissipation p d 200 mw operating junction and storage temperature t j, t stg ? 55 to ? 150 ? c note 1 : stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. n-channel jfet 15v, 10 to 32ma, 35ms sc-59 / cp3 3 1 2 electrical connection n-channel 1 2 3 1 : source 2 : drain 3 : gate ordering information see detailed ordering and shipping information on page 5 of this data sheet
nsvj3557sa3 www.onsemi.com 2 electrical characteristics at ta = 25c (note 2) parameter symbol conditions value unit min typ max gate-to-drain breakdown voltage v (br)gds i g = ? 10 ? a, v ds = 0v ? 15 v gate cutoff current i gss v gs = ? 10v, v ds = 0v ? 1 na cutoff voltage v gs(off) v ds = 5v, i d = 100 ? a ? 0.3 ? 0.7 ? 1.5 v drain current i dss v ds = 5v, v gs = 0v 10 32 ma forward transfer admittance | yfs | v ds = 5v, v gs = 0v, f = 1khz 24 35 ms input capacitance ciss v ds = 5v, v gs = 0v, f = 1mhz 10 pf reverse transfer capacitance crss 2.9 pf noise figure nf v ds = 5v, rg=1k ? , i d =1ma, f=1khz 1 db note 2 : product parametric performance is indicated in the elec trical characteristics for the listed test conditions, unless o therwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions.
nsvj3557sa3 www.onsemi.com 3
nsvj3557sa3 www.onsemi.com 4 package dimensions unit : mm sc-59 / cp3 case 318bj issue o xxx m xxx = specific device code m = date code = pb-free package generic marking diagram *this information is generic. please refer to device data sheet for actual part marking. 1 *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. (note: microdot may be in either location) notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimensions d and e1 do not include mold flash, pro- trusions, or gate burrs. mold flash, protrusions, or gate burrs shall not exceed 0.20 per side. 4. dimensions d and e1 are measured at the outermost extreme of the plastic body. 5. dimensions b and c apply to the flat section of the lead between 0.10 and 0.20 from the tip. dim a min max 0.95 millimeters a1 e 0.95 bsc a2 0.20 0.40 1.35 0.00 0.10 b 0.35 c d 2.75 3.05 0.50 0.10 0.20 e 2.30 e1 l 0.35 0.75 2.70 1.35 1.65 b e d 2 3 1 a1 a seating plane c side view a m 0.10 c top view a 3x e1 e l 3x a2 c 3x end view 1.00 3x dimensions: millimeters soldering footprint* 0.95 recommended pitch 3.40 0.80 3x
nsvj3557sa3 www.onsemi.com 5 on semiconductor and the on logo are registered trademarks of semiconductor components industries, llc (scillc) or its subsidiaries in the united st ates and/or other countries. scillc owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. a lis ting of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent-marking.pdf . scillc reserves the right to make changes with out further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any parti cular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specific ations can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated fo r each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc pro ducts are not designed, intended, or authorized for use as com ponents in systems int ended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees ar ising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that sci llc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject t oall applicable copyright laws and is not for resale in any manner. ordering information device marking package shipping NSVJ3557SA3T1G ir sc-59 3-lead / cp3 ? pb-free) 3,000 / tape & reel ? for information on tape and reel specifications, including part orientation and tape sizes, plea se refer to our tape and reel packaging specifications brochure, brd8011/d. http://www.ons emi.com/pub_link/collateral/brd8011-d.pdf
|
